MOUNTING A TUB

Mounting A Tub

Mounting A Tub

Blog Article

Request An Appointment

Here below yow will discover more good quality help and advice involving A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably hard project. If the old tub is easily available, the task can relocate quickly; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a house handyman's skills, although you will need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the task and also are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is better to think about employing one prior to you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly assist you set up a new tub in your bathroom if you have actually already acquired a new bathtub as well as do not require to alter the arrangement of your previous water pipes.
Your devices as well as material checklist must comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    First of all, the supporting frame provided with the bath should be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.

    Removing Old Taps


    If you require to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the instance.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
    Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little points.
    The next objective is to make certain that the bathtub is leveled all round. This can be attained by examining the level and changing the feet on the bathtub till the level reviews degree.
    To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
    Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if needed. Fill the bathtub and also check the overflow electrical outlet and also the regular outlet for leakages.
    Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the bath tub ought to wait till the tub has been made use of at least when as this will certainly resolve it right into its final placement.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet and also the sink. Safeguard the tap in place with the maker given backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a stiff seal, creating the water to penetrate the wall between the bath as well as the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to allow for the movement experienced when the tub is in use. The sealer can crack fairly early if you do not consider this motion before sealing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We hope you enjoyed our excerpt about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to read our piece. Enjoyed reading our entry? Please share it. Help somebody else discover it. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Contact


    Report this page